Tractor Pto Driveshaft Driveline Factory Hollow Spline Cardan Adapter Universal Joint Yoke Flexible Front Prop Rear CV Axle Propeller Automobile Drive Shaft

Application:

1. Agricultural Machinery

Tillage Equipment:

Rotary Tillers/Rotary Tillers: PTO drives rotating blades that break up and aerate the soil for seedbed preparation.

Plows: Some specialized plows or cultivators may use PTO power for active soil tillage.

Harvesting Equipment:

Hay Balers: PTO drives a mechanical device that picks up, compresses, and bundles hay or straw.

Forage Harvesters: Powers the cutting and chopping mechanism for silage production.

Combine Harvesters: While large combines have their own engines, the PTO can power certain attachments or smaller harvesters.

Mowing and Cutting:

Rotary Mowers/Brush Cutter: Power Take-Off (PTO) spins heavy blades for clearing stubborn brush and overgrown areas.

Precision Mowers: Powers precision mowing in lawns and fields.

Chain Mowers: Drives a rotating shaft with multiple chain pieces for mulching vegetation.

Seeding and Planting:

Drills/Seeders: PTOs can power metering systems or fan blowers for seeding.

Fertilizer Spreaders: Drives a rotating disc that evenly distributes granular fertilizer.

Spraying and Pumping:

PTO-Powered Sprayers: Powers a pump for spraying pesticides, herbicides, or liquid fertilizer.

Water Pumps: Used for irrigation or dewatering.

Other Farm Implements:

Diggers/Augers: PTOs drive an auger that drills holes in the ground for fencing or planting.

Grain Augers/Conveyors: Move grain from a trailer to a storage bin.

Manure Spreaders: Power an agitator or chain that spreads manure.

Wood Chippers: Drives a chipping mechanism for branches and logs.

2. Industrial and Commercial Equipment
In addition to agriculture, PTOs are used in a variety of industrial and commercial applications, often on trucks or specialized vehicles.

Onboard Equipment:

Dump Trucks: Powers the hydraulic pump that lifts the dump bed.

Garbage Trucks: Drives the compaction mechanism.

Tow Trucks/Wreckers: Powers the winch and hydraulic boom.

Concrete Mixer Trucks: Rotates the mixing drum.

Snowplows and Snowblowers: Powers the hydraulic system or screw conveyor that clears snow.

Vacuum Snow Suction Trucks: Drives the vacuum pump for suction.

Cranes and Lifts: Provides hydraulic power for various lifting and reaching functions.

Generators and Pumps:

Power Take-Off (PTO) driven generators: Provides power in remote areas or during power outages.

Industrial Pumps: Drives pumps for various fluid transfer applications.

Forestry and Landscaping:

Commercial Wood Chippers/Pulvers: Used to handle large amounts of wood debris.

Stump crusher: Provides power to the cutting wheel to remove tree stumps.
 

Step-by-step Installation Guide:

1.Safety First: Power Off and Secure Equipment

Make sure both the tractor/prime mover and implement are completely shut off. The tractor engine must be off and the power take-off (PTO) lever must be disengaged.

Set the parking brake on the tractor.

Block the wheels of the tractor and implement to prevent any unexpected movement.

Always wear appropriate personal protective equipment (PPE), including sturdy gloves and goggles.

2.Inspect the PTO and connections

Inspect the tractor's PTO stub shaft and the implement's input shaft. Make sure they are clean and free of rust, dirt and debris. Remove any old grease.

Inspect the PTO itself. Check the universal joints (U-joints), safety guards or extension tubes for any signs of damage, dents, cracks or excessive wear. Make sure all grease fittings are intact.

Verify that the locking devices (pins, collars or buttons) on both ends of the PTO shaft are clean and function smoothly.

3.Properly Position the PTO Shaft (Phase Alignment)

Most PTO shafts are designed to be "phase aligned," meaning the U-joints on each end must be properly aligned for smooth operation and to prevent vibration.

If the PTO shaft is split into two halves:

Align the halves so that the U-joints on each end are in phase. This means that the yokes (the "forked" parts) on each end of the shaft should be aligned on the same plane. If one U-joint is horizontal, the other should also be horizontal.

Slide the halves together. Make sure there is enough overlap between the inner and outer extension tubes (usually 1/3 to 1/2 the length of the inner tube, check the manufacturer's manual).

4.Connect to the Implement

First connect the implement end of the PTO shaft to the implement's input shaft.

Pull back on the locking ring/button on the PTO shaft yoke.

Slide the yoke onto the implement's splined input shaft.

Loosen the locking ring/button, making sure it is securely engaged with the groove on the implement shaft. Pull firmly on the PTO shaft to verify that it is securely locked in place. It should not fall out when pulled.

5.Attach to Tractor

Now connect the tractor end of the PTO shaft to the tractor's PTO stub shaft.

Pull back on the locking ring/button on the PTO yoke.

Slide the yoke onto the tractor's splined PTO stub shaft.

Loosen the locking ring/button, making sure it engages securely with the groove on the tractor shaft. Pull firmly on the PTO shaft to verify that it is securely locked in place. It should not fall out when pulled.

6.Check Length and Clearance

Raise and lower the implement through its full range of motion using the tractor's 3-point hitch (or hydraulic controls).

Observe the length of the PTO shaft:

At maximum extension: Make sure there is still enough overlap between the telescoping tubes (at least 1/3 to 1/2 overlap). If not, the PTO shaft is too short and needs a longer shaft.

At maximum compression (shortest length): Make sure the telescoping tubes do not "bottom out" (hit their internal stops). If it bottoms out, the PTO is too long and needs to be shortened (cut an equal amount of shaft from each half of the telescope tube per the manufacturer's instructions), or a different length PTO is needed. Bottoming out can cause serious damage to the PTO, implement, or tractor.

Check Play: Make sure the PTO does not interfere with any part of the tractor or implement through its full range of motion.

7.Grease the Power Take-Off (PTO)

Locate all grease fittings on the universal joints and telescope tubes (usually located under the safety guards).

Use a grease gun to apply a liberal amount of grease until new grease comes out of the universal joint or telescope tube. Lubricate the telescope.

This step is critical for smooth operation and long life.

8.Install Safety Guards

Make sure all PTO safety guards are properly installed and securely attached. Never operate a PTO shaft without a guard. This is a critical safety measure to prevent entanglement injuries.





 

Company information: